Structural Fire Damage Cleaning in Patchogue, NY
The drywall is gone, and now you are staring at blackened studs, scorched joists and a charred roof deck. Somebody now has to decide what gets blasted clean, what gets sistered and what gets replaced. Unify Fire Solutions connects you with independent, licensed and insured contractors in Patchogue who clean the framing, masonry and steel itself.
- Soda blasting, dry ice blasting and wire brushing
- Every stud and joist probed for char depth
- Cleaned wood encapsulated against lingering odor
Why the Bare Structure Needs Its Own Crew
Close up the walls over dirty framing and the smoke odor bleeds right back through the new finish. Cleaning the structure is the step that decides whether the rebuild smells like a new house or a campfire.
Licensed & Insured Independent Pros
Each contractor on our referral list is an independent, licensed and insured local company. Check the paperwork yourself and ask if their process lines up with IICRC S700.
Upfront Written Estimates
Media blasting depends on square footage, the media used and how hard the space is to get into. Get a written, itemized estimate in hand before any blasting begins.
Rapid Local Dispatch
A real person answers around the clock, and the search for a crew begins on that call. Timing depends on which crews near Patchogue are free, and it is often the same day.
Blasting Rigs and Probing Tools
Structural crews bring soda blast pots, dry ice units, big compressors, HEPA vacs, air scrubbers and a sharp awl to test every member.
Do not climb into a burned attic or walk a scorched roof deck to look for yourself. Weakened joists and burned-through sheathing can give way without warning, and exposed wiring may still be live. Let the crew confirm the structure will hold before anyone goes up, and keep everyone off the floor above a burned basement or crawlspace.
Structural Cleaning Services From Rafters to Slab
This is not contents cleaning and it is not debris haul-out. This page is about the framing, masonry and steel that actually carry the load.
Char Depth Probing and Member Decisions
Pressing an awl into the blackened wood shows how deep the char goes; a shallow crust over firm wood usually means it can be cleaned. Deep char that eats into the section of a joist or truss chord means sistering or replacement.
- Members marked clean, sister or replace
- Structural engineer called in for questionable beams, trusses and headers
- Photos of each marked member for the claim
Soda Blasting
Sodium bicarbonate is softer than wood, so it strips soot and light char off studs, joists and roof decking without gouging the grain. Expect fine dust and residue that has to be contained and HEPA vacuumed when the blasting is done.
Dry Ice Blasting
Dry ice pellets hit the surface and turn straight into gas, so there is no media left behind to sweep up. It suits cramped attics and areas around wiring, but it runs louder and pricier than soda.
- Hearing protection and ventilation required
- Good choice when residue would be a problem
Wire Brushing and Sanding
Small, isolated char spots are often handled by hand with wire brushes and sanders tied into a HEPA vacuum. It is slow on big areas but precise where blasting would be overkill.
Brick, Block, Concrete and Steel Beams
Fireplace surrounds, block foundation walls and concrete slabs hold soot in their pores, and alkaline cleaners, scrubbing or blasting pull it out. Steel beams and columns are cleaned of soot and checked for warping or sag, which goes to the engineer.
Encapsulation and Attic Insulation Removal
Even well-blasted wood can hold faint odor in its pores, so crews roll or spray a pigmented shellac-based or specialty encapsulating sealer over cleaned framing. In the attic, smoke-soaked blown-in or batt insulation is vacuumed out with a high-powered insulation vac before the rafters and decking are cleaned.
Crawlspaces get the same treatment on a smaller, dirtier scale: floor joists, sill plates and the underside of the subfloor are probed, blasted where needed and sealed. A smoke-stained or wet vapor barrier usually comes out and goes back new.
Have the contractor explain the method they plan for each part of the house. It is common to see soda in open walls, dry ice in the attic and hand sanding near the electrical panel on the same job.
Containment matters here, since blast media and loosened soot travel anywhere the air moves. The crew hangs poly over doorways, masks off the HVAC returns and runs air scrubbers under negative pressure while they work. Ask what the plan is to shield the undamaged rooms, floors and glass.
Looking at Blackened Studs and Rafters?
Phone our dispatchers and they begin searching for a structural crew close to Patchogue. It costs nothing to call.
Call +1-833-336-1630How a Structural Cleaning Job Unfolds
- 1
Phone the Dispatcher
Describe what is exposed: open stud walls, an attic, a crawlspace, block or steel. Let us know if an adjuster, engineer or roofer has already visited.
- 2
Mobile Crew on Site
An independent crew shows up with its compressor, blast gear, poly and air scrubbers. First they confirm the roof deck and floors will hold weight and that the exposed circuits are dead.
- 3
Probe, Mark and Quote
Every exposed member gets probed with an awl and marked clean, sister or replace, and anything borderline goes to a structural engineer. A written, itemized quote covering area, blast method, encapsulant and attic insulation comes before any work starts.
- 4
Blasting, Sealing and Walkthrough
After blasting and HEPA cleanup, the framing gets its sealer coat, and you walk the bare structure with the crew lead. Do a sniff test on a warm afternoon, and ask for photos of every marked member before the rebuild closes the walls.
What Callers Said About Their Structural Crew
After the attic fire, the rafters were black and the blown-in insulation was a wet mess. They vacuumed out the insulation, dry iced the rafters around the wiring and sealed it all. Two rafters were cut deep enough that they called in an engineer, and those got sistered.
My contractor brother-in-law said all the black studs had to go. The crew lead pushed an awl into each one and showed me the wood was solid under a thin crust. Soda blasting and a coat of sealer saved most of the wall.
The fire in our lower level left the block walls and the steel beam coated in soot. They scrubbed and blasted the block, cleaned the beam and had the engineer confirm it had not sagged. The basement smells normal again, even closed up.
Common Questions About Cleaning Charred Framing
How do crews decide if a charred stud can stay?
The test is simple: they probe it. Push an awl into the char, and if it hits solid wood after a shallow layer, the stud is usually a cleaning job. Members with deep char, splitting or a lost cross section get sistered or replaced, and anything structural in doubt goes to a licensed structural engineer.
What is the difference between soda blasting and dry ice blasting?
Soda blasting uses sodium bicarbonate media that is gentle on wood and helps neutralize odor, but it leaves dust and residue to clean up. Dry ice pellets vanish on impact, so cleanup is easier and it works well around wiring, but it is louder and usually costs more. Many crews use both on the same house.
Why seal the framing if it has already been cleaned?
Smoke gets deep into the pores of the wood, past what blast media can reach. A shellac-based or specialty encapsulant locks that residual odor in so it cannot off-gas through the new drywall. Sealer only works over clean framing, never as a shortcut over soot.
Does the attic insulation have to come out after a fire?
In most cases where smoke got into the attic, it does. Loose-fill and batts act like a giant filter for smoke, and hose water often soaks them as well. Crews vacuum it out with a truck-mounted or portable insulation vac so the rafters and decking can be inspected and cleaned before new insulation goes in.
Can soot be cleaned off brick and concrete block?
Usually yes, though masonry takes more effort than drywall because soot sinks into the pores. Expect alkaline detergents and scrub brushes for light staining and media blasting for thick deposits. Heat-cracked or spalled block and brick should be looked at by an engineer or mason.
Do I need a structural engineer for fire-damaged framing?
Not for every job, but for anything load-bearing that looks questionable, yes. Trusses, beams, headers, steel and heavily charred joists are where an engineer's letter protects you and helps the claim. Your local building department may also require one before the walls close.
Charred Framing Cleaning Across Patchogue and Beyond
Our dispatch line covers Patchogue and the nearby communities around it, from older homes with plaster and solid-sawn joists to newer builds with engineered trusses. Attics, basements, crawlspaces, garages and light commercial spaces all come up regularly.
- Attic fires
- Electrical fires
- Furnace puff-backs
- Chimney fires
- Lightning strikes
- Neighbor's fire spread
If the first crew we connect you with is not the right fit, call back and a dispatcher will connect you with another. Get the bones cleaned before anyone hangs new drywall.
